久久久久久久久久网站-久久久久久久久久免费视频-久久久久久久久久免费-久久久久久久久久久影院-一级毛片一级毛片-一级毛片一级黄片

s
(1) When using Microsoft
R
Windows NTR
Workstation Operating System Version 4.0
and Microsoft
R
WindowsR
2000 Professional Operating System
When using Windows NTR
Workstation 4.0 and WindowsR
2000 Professional,
MX Component may be installed and used only on the administrator's authority.
(2) About Ethernet communication, computer link communication and CPU COM
communication on Microsoft
R
WindowsR
95 Operating System
(a) Making Ethernet communication using TCP/IP and UDP/IP on WindowsR
95
of the version older than OSR2 will cause a memory leak. When performing
continuous operation on WindowsR
95, use WindowR
95 OSR2 or later.
(b) On WindowsR
95, communication using the COM port, e.g. computer link
communication or CPU COM communication, will cause a memory leak.
Therefore, do not perform continuous operation.
(3) About installation
(a) When performing overwrite installation, install the software in the folder
where it had already been installed.
(b) If you install the MELSEC board driver or GX Developer into the personal
computer where MX Component has already been installed, communication
using a specific path (e.g. ASCII packet of the AJ71E71) may result in a
receive, device number or other error.
If any of these phenomena has occurred, perform overwrite installation of MX
Component again.
(4) Precautions for performing installation and uninstallation on a dual boot machine
where two different operating systems are installed in a single IBM-PC/AT
compatible personal computer
On a dual boot machine having Windows NTR
Workstation 4.0 (hereafter referred to
as OS1) and WindowsR
95/98 (hereafter referred to as OS2), note the following points
when MX Component was installed on OS1 first and MX Component was then
installed over the same folder on OS2.
(a) If MX Component is uninstalled first on the OS2 side, uninstallation does not
delete the control DLLs and ACT folders, and they remain within the IBM-
PLC FX2NC-16MR-T-DS
PLC FX3U-128MR/ES-A
DC 輸入/繼電器輸出模塊 AX80Y14CEU
PLC FX1S-30MR-001
PLC FX2N-32MT-ES/UL
模擬量輸出擴展板 FX1N-1DA-BD
直流漏型輸入模塊 A1SX41-S2
輸入模塊 AX80E
可控硅輸出單元 FX2N-32ES
晶體管輸出單元 FX0N-40ET
PLC FX2NC-16MT-D/UL
PLC FX2N-128MR-D
繼電器輸出模塊 FX2N-8EYR
PLC FX1S-14MT-001
模擬量輸入擴展板 FX1N-2AD-BD
PLC FX3U-128MT/ES-A
可編程控制器 FX1N-40MT-001
CC-Link IE控制器網絡通信單元 GT15-J71GP23-SX
擴展模塊 FX2N-16EX
RS-485適配器 FX3U-485ADP
模擬量輸入擴展板 FX2N-2AD-BD
PLC FX1S-20MR-ES/UL
小型CPU長距離連接電纜 GT15-C200EXSS-1
輸入模塊 AX81C
PLC FX2N-128MT-D
輸入模塊 AX81B
擴展板 FX2N-CNV-BD
輸入模塊 A1SX40-S1
存儲卡 FX2N-ROM-E1
CC-Link用主站模塊 FX2N-16CCL-M